Swivel clamps are very simple, but effective car rigging equipment that is used by almost every entry-level and experienced rigger on the market today. If you’re thinking about getting into car rigging as a hobby or profession, then it’s important to understand how to properly use swivel clamps while rigging your vehicle.
This guide will outline the steps and show you some examples of how you can use car rigging swivel clamps in different situations. Swivel clamps can be purchased at most local hardware stores, which makes them very easy to pick up and start using right away!
types of car rigging swivel clamps
There are three types of car rigging swivel clamps and they come in various sizes.
- The first type is a spring clamp, which will provide the most holding power but can be difficult to attach to curved surfaces.
- The second type is a strap clamp, which is easier to attach and release but may slip down and loosen over time.
- The third type is called an expandable grip clamp. It has the same general properties as a strap clamp but it provides more holding power than either the spring or strap version.
How is rigging swivel clamps work?
Swivel clamps are a crucial part of car rigging that enables you to keep your straps tight and in place. They attach the strap from one side of the car to the other. One end attaches to an anchor point on one side of the vehicle, while the other end attaches at a point on the opposite side. A swivel is then used by connecting it securely on each anchor point with a bolt or screw, and then tightening them with a wrench.
Prepare
To begin your installation, you’ll want to find where on the vehicle the first clamp will be installed. The first step is getting the right fit. You’ll want to measure the height and width of your bumper or fender, then select a clamp that fits snugly within these dimensions. Once you have it in place, you’ll want to tighten it by spinning the knob on top clockwise
Installing Them On Your Car
Once you’ve found a spot for installing the first clamp, drill holes into either side of where you plan to install it and make sure they line up perfectly before driving screws or bolts into those holes. Connecting both sides of the car together, tighten all bolts or screws with a wrench. Repeat these steps until you have all clamps in place. Keep in mind that a maximum number of six clamps should be used per side.
Also, when attaching cables between the two points, always leave enough slack so that it does not put too much pressure on any one point and cause damage to the vehicle or person being rigged. After following these steps carefully, you’re now ready to rig your car!
attach the cables
Once the clamps are on your car, you need to attach the cables. You will typically find two ends of cable: one that attaches to the top of your car and one that attaches under your car. If you are trying to tow a trailer, you’ll want to attach the cables under your car, but if not, go ahead and attach them at the top of your car. To do this, take each end and thread it through the hole in its corresponding car rigging swivel clamps.
Thread the loose end through the I-shaped part of the other clamp. The I-shaped part should be facing away from your car and toward the ground. Bring the ends together and twist them once or twice (enough so they don’t slide apart). Tighten them by pulling firmly on both sides simultaneously until snug.
Make sure there is enough slack between the cable and clamp for easy movement, but not too much slack that they can pull apart or accidentally come off during operation. Now try moving the vehicle back and forth to ensure that the wires are not caught up on anything. It’s also important to make sure the cables cannot interfere with the steering or shift levers as you drive.
Read Also: Trigger Clamps Vs Bar Clamps vs pipe clamps
benefits of car rigging swivel clamps
Swivel clamps are a tool that is used in the rigging process of a car. They are used as pivoting points, which allows for quick and easy adjustments of the car’s rigging. The main benefits of car rigging swivel clamps are that they are lightweight, inexpensive, and can be used with any type of rope or cable.
- First, swivel clamps are much easier to use than traditional clevises and provide more options for how you want your car rigged.
- Second, if you have an issue with your setup it will be easier to adjust it because of how quickly you can manipulate the clamps.
- Third, because these clamps don’t require any tools or drilling into anything there is less damage done during the rigging process.
- Lastly, swivel clamps are much lighter than other forms of rigging hardware so they make moving around your car easier.
Storing them in your toolbox
Once you have finished using the swivel clamps, always be sure to store them in your toolbox where they will not cause any damage. If you will not be using them for an extended period of time, it is best to remove the clamps from your toolbox and store them in a separate location so that they do not become damaged by other tools. Be careful not to overtighten these clamping devices as this can result in stripped threads or a broken component.
One way to avoid this problem is by loosening all connections on the component that needs rigging before tightening the last one uptight. When removing screws and bolts during car rigging, make sure you tighten them securely with proper torque specifications but also avoid over-tightening them.
Read More about swivel clamps
